CTY ÂU MỸ CHUYÊN CUNG CẤP BỘ [BỘ CHIA TÍN HIỆU]

BỘ CHIA DN22000 CỦA HÃNG DRAGO THAY THẾ CHO CÁC HÃNG NHƯ M-SYSTEM, WEIDMULLER, PEPPERL FUCHS, SENECA, WAGO, KONICK, MTL....

HÀNG ĐƯỢC NHẬP VỀ TỪ ĐỨC CÓ ĐẦY ĐỦ C.O VÀ C.Q

ĐỘ SAI SỐ THẤP: 0.1%

CÁCH LY 3KVA

NGUỒN CẤP POWER RAIL HOẶC TERMINAL

KÍCH THƯỚC SIÊU MỎNG: 6MM

THÔNG SỐ KỸ THUẬT:

Technical Data

Input

Input signal (calibrated switchable)	0 to 20 mA, 4 to 20 mA, 0 to 5 V, 0 to 10 V, 1 to 5 V, 2 to 10 V
Input resistance	Current input Voltage input	≤ 35 Ohm ≥ 100 kOhm
Overload	Current input Voltage input	< 50 mA < 30 V
Transmitter supply Tx (switchable)	16 V (open circuit voltage/short circuit current ≤ 22 V/35 mA)

Output I + II

Output signal (calibrated switchable)	0 to 20 mA, 4 to 20 mA, 0 to 5 V, 0 to 10 V, 1 to 5 V, 2 to 10 V
Load	Current output: ≤ 6 V (300 Ohm at 20 mA)	Voltage output: ≤ 5 mA (2 kOhm at 10 V)
Linear transmission range	-1 to +110 %
Ripple	< 10 mVrms

General Data

Transmission error	< 0.1 % full scale
Temperature coefficient 1)	< 100 ppm/K
Cut-off frequency -3 dB	5 kHz
Response time T99	150 µs
Test voltage	3 kV AC, 50 Hz, 1 min, Input against Output I against Output II against power supply
Working voltage 2) (Basic Insulation)	Up to 600 V AC/DC for overvoltage category II and pollution degree 2 acc. to EN 61010-1 between all circuits.
Protection against electrical shock	Protective separation according to EN 61140 by reinforced insulation in accordance with EN 61010-1 up to 300 V AC/DC for overvoltage category II and pollution degree 2 between all circuits.
Ambient temperature	Operation Transport and storage	–25 °C to +70 °C   (-13 to +158 °F) –40 °C to +85 °C   (-40 to +185 °F)
Power supply	24 V DC       16.8 V to 31.2 V DC, approx. 1.4 W
EMC 3)	EN 61326-1
Construction	6.2 mm housing, protection class: IP 20, mounting on 35 mm DIN rail acc. to EN 60715
Weight	Approx. 70 g

1. Average TC based on the final value in specified operating temperature range
2. As far as relevant the standards and rules mentioned above are considered by development and production of our devices. In addition relevant assembly rules are to be considered by installation of our devices in other equipments. For applications with high working voltages, take measures to prevent accidental contact and make sure that there is sufficient distance or insulation between adjacent situated devices.
3. Minor deviations possible during interference

Block diagram

Dimensions

Connection
Captive plus-minus clamp screws
Wire cross-section max. 2.5 mm² / AWG 14
Stripped length 6 to 8 mm / 0.28 in
Screw terminal torque 0.8 Nm / 7 lbf in
Optional power connection via In-Rail-Bus (see accessories)

Terminal assignments

LIÊN HỆ ĐỂ ĐƯỢC TƯ VẤN VÀ GIÁ TỐT:

MR. LONG - 0909 006 4350909 006 435 

EMAIL: [email protected]  HOẶC  [email protected]

WEB.: WWW.CHUYENDOITINHIEU.COM

          WWW.AUMYCO.COM

          WWW.TBCONGNGHIEP.COM

          WWW.DOLUONGCONGNGHIEP.COM

Sản phẩm doanh nghiệp: Cty TNHH Thương Mại Dịch Vụ Công Nghệ ÂU MỸ